Steam is generated in main generation plants, and/or at various process units using heat from flue gas or other sources. Heaters (furnaces) include burners and a combustion air system, the boiler enclosure in which heat transfer takes place, a draft or pressure system to remove flue gas from the furnace, soot blowers, and compressed-air systems that seal openings to prevent the escape of flue gas. Boilers consist of a number of tubes that carry the water-steam mixture through the furnace for maximum heat transfer. These tubes run between steam-distribution drums at the top of the boiler and water-collecting drums at the bottom of the boiler. Steam flows from the steam drum to the superheater before entering the steam distribution system.
Heaters may use any one or combination of fuels including refinery gas, natural gas, fuel oil, and powdered coal. Refinery off-gas is collected from process units and combined with natural gas and LPG in a fuel-gas balance drum. The balance drum provides constant system pressure, fairly stable Btu-content fuel, and automatic separation of suspended liquids in gas vapors, and it prevents carryover of large slugs of condensate into the distribution system. Fuel oil is typically a mix of refinery crude oil with straight-run and cracked residues and other products. The fuel-oil system delivers fuel to process-unit heaters and steam generators at required temperatures and pressures. The fuel oil is heated to pumping temperature, sucked through a coarse suction strainer, pumped to a temperature-control heater, and then pumped through a fine-mesh strainer before being burned. In one example of process-unit heat generation, carbon monoxide boilers recover heat in catalytic cracking units as carbon monoxide in flue gas is burned to complete combustion. In other processes, waste-heat recovery units use heat from the flue gas to make steam.
The distribution system consists of valves, fittings, piping, and connections suitable for the pressure of the steam transported. Steam leaves the boilers at the highest pressure required by the process units or electrical generation. The steam pressure is then reduced in turbines that drive process pumps and compressors. Most steam used in the refinery is condensed to water in various types of heat exchangers. The condensate is reused as boiler feedwater or discharged to wastewater treatment. When refinery steam is also used to drive steam turbine generators to produce electricity, the steam must be produced at much higher pressure than required for process steam. Steam typically is generated by heaters (furnaces) and boilers combined in one unit.
Feedwater supply is an important part of steam generation. There must always be as many pounds of water entering the system as there are pounds of steam leaving it. Water used in steam generation must be free of contaminants including minerals and dissolved impurities that can damage the system or affect its operation. Suspended materials such as silt, sewage, and oil, which form scale and sludge, must be coagulated or filtered out of the water. Dissolved gases, particularly carbon dioxide and oxygen, cause boiler corrosion and are removed by deaeration and treatment. Dissolved minerals including metallic salts, calcium, carbonates, etc., that cause scale, corrosion, and turbine blade deposits are treated with lime or soda ash to precipitate them from the water. Recirculated cooling water must also be treated for hydrocarbons and other contaminants. Depending on the characteristics of raw boiler feedwater, some or all of the following six stages of treatment will be applicable:
- Clarification;
- Sedimentation;
- Filtration;
- Ion exchange;
- Deaeration; and
- Internal treatment.
The most potentially hazardous operation in steam generation is heater startup. A flammable mixture of gas and air can build up as a result of loss of flame at one or more burners during light-off. Each type of unit requires specific startup and emergency procedures including purging before lightoff and in the event of misfire or loss of burner flame. If feedwater runs low and boilers are dry, the tubes will overheat and fail. Conversely, excess water will be carried over into the steam distribution system and damage the turbines. Feedwater must be free of contaminants that could affect operations. Boilers should have continuous or intermittent blowdown systems to remove water from steam drums and limit buildup of scale on turbine blades and superheater tubes. Care must be taken not to overheat the superheater during startup and shut-down. Alternate fuel sources should be provided in the event of loss of gas due to refinery unit shutdown or emergency. Knockout pots provided at process units remove liquids from fuel gas before burning.